Electronics Components Name And Symbol Pdf

electronics components name and symbol pdf

File Name: electronics components name and symbol .zip
Size: 22564Kb
Published: 20.05.2021

Today, circuit symbols and their usage has been pretty much standardised.

A ground symbol IEC symbol identifies a ground terminal. It can be used for a zero potential reference point from where current is measured. It is also for electrical shock protection. There are a few different ground symbols. A resistor reduces current flow.

Electronic Components - Functions&Symbols

Electronic component symbols are used to denote the components in circuit diagrams. There are standard symbols for each of the components which represent that particular component. Here in this article, we are explaining some basic and mostly used electronic components with their symbols. Symbol of the resistor is represented by Zig-Zag lines between two terminals. It is a common and widely used symbol in schematics.

It can also be represented by another symbol that has an unfilled rectangle between two terminals instead of Zig-Zag lines. The resistor is a non-polarized component that means both sides have the same polarity and can be connected from both sides.

The capacitor is a two-terminal component denoted by C. Symbol of the capacitor looks like the two parallel plates are placed in between two terminals.

In the schematic, two types of capacitor symbols are available. One is for a polarized capacitor and the other one is for the non-polarized capacitor. Learn more about capacitors here and check about various types of capacitors. The difference between both the symbols is that in the polarized capacitor symbol, one parallel plate has a curved shape.

The curved plate represents the cathode of the capacitor and should be at a lower voltage than the anode pin plane-parallel plate. As the name indicates, a non-polarized capacitor can be connected in two ways but for polarized capacitor only specified one-way Connection is possible.

The value of the capacitor is measured in farads f. The diode is a polarized device with two terminals and denoted by D. In a diode, one terminal is positive anode and another one is negative cathode.

The closed side of a triangle is the cathode, and the base of a triangle is an anode. The symbol of a diode looks like a horizontal isosceles triangle pressed up against a line between two terminals. The diode works in the forward bias or we can say that the diode will let the current flow in the forward bias condition. Therefore, it is important to note that the positive terminal anode of the diode is connected to the positive pole of the battery and negative pole cathode of the diode is connected to the negative terminal of the battery.

There are some other diodes with additional specifications and features explained below. Also, check various diodes and their working here. LED stands for light-emitting diode. The LED symbol is similar to the diode symbol with additional arrows.

These arrows appear to point in the opposite direction of the triangle and seem to radiate from the triangle. LED is a polarized component with anode and cathode terminals. Arrows striking the diode represent photons or light. The photodiode has two terminals named anode and cathode. A photodiode is used to convert light into electrical current. It is similar to the normal forward diode; it also allows reverse current when the applied voltage reaches the breakdown voltage.

The diode has a special, heavily doped P-N junction, which is designed to operate in the reverse direction when a certain specified voltage is reached. Learn more about it by going through various Zener Diodes. The Schottky diode has a lower forward voltage drop than the PN junction diode, and it is a metal-semiconductor diode. It can be used in high-speed switching applications.

The Schottky diode is a unipolar device because it has electrons as majority carriers on both sides of the junction. For this reason, electrons cannot flow across the Schottky barrier. Under the forward biased condition, an electron present on the N side receives more energy to cross the barrier and enter into the metal. Therefore, the diode is called a hot carrier diode. Due to this, the electrons are also called hot charge carriers. The transistor is a three-terminal device that amplifies or switches electronic signals and electrical power.

We have previously covered various Transistors with their symbols, pinouts, and specifications. For the BJT symbol, emitter and collector are arranged in a line and the base is arranged vertically. You can remember the configuration like this. An inductor is a non-polarized two-terminal component. The international symbol of an inductor considers a filled-in rectangle instead of loopy coils.

Here are few Inductors with their pinouts and working. Logic gates are the fundamental building blocks of any digital system.

Logic gates have two inputs and one output however, the number of inputs can be changed as per the requirement while the output should be the same. All the logic gates have a unique schematic symbol as shown below.

Switches are electronic devices designed to interrupt or divert the flow of electric current or signals in a circuit. The simplest switch, a single-throw switch SPST , consists of two terminals with a semi-connected lead representing the actuator. All 4 switches have different symbols, although the number of poles and throws changes in symbol according to their name. Symbols are given below to clear the illustration. The power supply is an essential part of any electrical or electronic system.

While selecting an accurate power supply, various requirements must be considered. There is a variety of power supply circuit symbols that indicate the power source. Generally, constant voltage sources are used while working with electronics. Instead of a constant voltage source, you can also use batteries. The battery symbol looks like a pair of disproportionate parallel lines, while more line pairs usually indicate more row cells in the battery.

Voltage nodes are single-terminal schematic components that are used to denote power supply and can also be connected to component terminals to specify a specific voltage level. The device can be directly connected to this one-terminal symbol which denotes 5V, 3. Positive voltage nodes are usually indicated by an Up-pointing arrow, while ground nodes typically include one to three flat lines or sometimes down-pointing arrows or triangles as shown in the image above.

A transformer is a static device that transmits electrical energy from one circuit to another through electromagnetic induction. The transformer symbol is denoted by two coils placed side by side, and separated by parallel lines.

They are generally used to step up or step down the voltage levels. Relay is an electromagnetic switch that can be turned on with small electrical current which further allows a large amount of current to flow from it. It usually pairs a coil with a switch which can be seen in the symbol itself.

The relay has 5 pins consisting of a pair of coil pins, a common pin, a normally open pin NO , and a normally closed pin NC. We previously covered a detailed article on Relay and its working.

In buzzer, there is usually an oscillating transistor circuit, so it produces sound whenever a voltage is applied to it. The buzzer is a polarized component and can only be connected with a positive terminal to positive and negative to negative. A speaker can play all kinds of sound. However, due to its integrated circuits, a buzzer is only able to compose the tone of the oscillator. Learn more about Buzzer and Speaker by following the links.

The motor is a transducer that converts electrical energy into kinetic energy motion. The motor symbol looks like an embellishment encircled 'M' around the terminals. We have covered various types of motors with their symbol and working. A fuse or a PTC is an electrical safety device that provides overcurrent protection for a circuit. The PTC symbol is actually the general symbol for a thermistor. Below table shows the unit, pin name and no of terminals of all the components we covered above:.

So this is a beginner guide to learn about different types of basic electronic components, their symbols, and working. The STM32Cube with graphical software configuration tool reduces development efforts, time, and cost. Electronic Component Symbols.

Click to Enlarge. Tags Component Symbols. Related Post. Leave a Reply Please Login. STM32F32 Ecosystem. All rights reserved.

Electronic Component Circuit Symbols

Track My Order. Frequently Asked Questions. International Shipping Info. Send Email. Mon-Fri, 9am to 12pm and 1pm to 5pm U.

In electronic circuits, there are many electronic symbols that are used to represent or identify a basic electronic or electrical device. NO changes can be brought by the user on any electronic symbol, but the user is free to bring any changes in the architectural drawings like power source and lighting. The symbols for different electronic devices are shown below. Click on each link given below to view the symbols. Apart from the circuit symbols, each device is also designated a short name. Though these names are not approved as standard notations, they are commonly used by most people.

Electronic symbol

An electronic symbol is a pictogram used to represent various electrical and electronic devices or functions, such as wires , batteries , resistors , and transistors , in a schematic diagram of an electrical or electronic circuit. These symbols are largely standardized internationally today, but may vary from country to country, or engineering discipline, based on traditional conventions. The graphic symbols used for electrical components in circuit diagrams are covered by national and international standards, in particular:. The number of standards leads to confusion and errors. For example, lighting and power symbols used as part of architectural drawings may be different from symbols for devices used in electronics.

Electrical Symbols

Electronic gadgets have become an integral part of our lives. They have made our lives more comfortable and convenient. From aviation to medical and healthcare industries, electronic gadgets have a wide range of applications in the modern world.

Electronic component symbols are used to denote the components in circuit diagrams. There are standard symbols for each of the components which represent that particular component. Here in this article, we are explaining some basic and mostly used electronic components with their symbols. Symbol of the resistor is represented by Zig-Zag lines between two terminals. It is a common and widely used symbol in schematics.

 Ну да? - Он хмыкнул.  - Давай я тебе помогу.

Когда службы безопасности выдворяли его из страны, он успел сказать несколько слов Стратмору, причем произнес их с ледяным спокойствием: - Мы все имеем право на тайну. И я постараюсь это право обеспечить. ГЛАВА 7 Мозг Сьюзан лихорадочно работал: Энсей Танкадо написал программу, с помощью которой можно создавать шифры, не поддающиеся взлому. Она никак не могла свыкнуться с этой мыслью.

Electrical Symbols

 Готово! - крикнула Соши. Все посмотрели на вновь организованный текст, выстроенный в горизонтальную линию. - По-прежнему чепуха, - с отвращением скривился Джабба.

How Electronic Components Work

Это резиновая капсула, которая при попадании растворяется. Все тихо и чисто. Перед сердечным приступом мистер Танкадо не почувствовал ничего, кроме легкого укола. - Травматическая пуля, - задумчиво повторил Беккер.

How to Read a Schematic




in PDF. Free downloads of PDF files with all electrical symbols, for consultation and printing on A4 sheets. These electrical drawing symbols represent electrical components, devices and circuits. Symbol, Family, Symbol, Family. Actuators and Diodes, Logic Circuits Symbols (Digital Electronics), - Logic circuits.

Esculapio S.


This pool of electrons is available for electronic components to use. Capacitance is measured in Farads. The small capacitors usually used in electronics are.

Mathilde P.


High performance with high integrity pdf writer best format for pdf portfolio

Liane C.


Army pay chart 2014 pdf high performance with high integrity pdf writer